NEWS EVENTS
Oxygen-Permeable Release vs. FEP/PFA Film: Two Release Mechanisms in Vat Photopolymerization
2026-11-21

In vat photopolymerization, how the cured layer separates from the vat window governs both print stability and part quality. Two approaches dominate this interface: low-surface-energy release films such as FEP and PFA, and oxygen-permeable membranes that maintain an inert, oxygen-rich interface. Drawing on peer-reviewed literature, this article compares the two routes in terms of interfacial mechanism, parameter sensitivity, and practical boundaries.
1. Release force and why it dictates build quality
Vat photopolymerization builds parts layer by layer. After each layer cures, adhesion develops between the part and the window film; the build platform must overcome that adhesion to lift the layer free. The force required is the release force — also called peel or separation force — and it is one of the most consequential variables in the process.
Abnormal release force translates directly into defects. A 2025 study in Engineering Plastics Applications reported that, in DLP printing, resin temperature fluctuation and irregular release force at the cured-layer/film interface readily cause warping, cracking, or parts detaching from the build platform, significantly degrading both quality and throughput. The authors built a multi-parameter monitoring system around an STM32F407 microcontroller, integrating a 0–50 N load cell, a ±0.5 °C thermocouple, and a liquid-level sensor to close the loop on release force and resin temperature.[1] Controlling release force is not optional — it is central to process stability.
2. Low-surface-energy films: FEP and PFA measured head to head
Conventional bottom-up photopolymerization relies on low-surface-energy films to reduce adhesion at the cured-part/film interface and allow each layer to peel away. A 2026 study in the Journal of Printing and Digital Media Technology Research compared FEP and PFA films for mechanical performance and release force, then used an orthogonal experiment to rank the influence of printing parameters.[2]
The result: PFA outperformed FEP on both mechanical properties and release force. After parameter optimization, release force fell from 3.85 N to 1.63 N. Ranked from weakest to strongest, the parameters affecting release force were exposure time, layer thickness, light power, and lift (peel) speed.[2] In practice, when release force runs high or builds become unstable, adjust peel speed first, then light power and layer thickness, and treat exposure time as the last lever.
One caveat: that experiment used an LCD system. Its findings quantify how material and parameters influence release force, but they should not be extrapolated directly to continuous printing. A low-surface-energy film still separates by layer-by-layer peeling — only the force changes.
3. Oxygen-permeable membranes: a continuous build interface via oxygen inhibition
Oxygen-permeable membranes work on a fundamentally different principle. The concept traces to Continuous Liquid Interface Production (CLIP), introduced by Carbon in 2015. The associated Science paper describes an amorphous fluoropolymer window (DuPont Teflon AF 2400) with an oxygen permeability of roughly 1,000 barrer, combining UV transmission with chemical inertness. Oxygen permeates the window continuously and sustains an oxygen-inhibited "dead zone" tens of micrometres thick between the part and the window. Resin in that zone stays liquid, so the part can be lifted continuously without peeling layer by layer.[3] Carbon's patent literature likewise identifies Teflon AF 2400 as the window material, with a typical dead-zone thickness of 20–30 µm.[4]
Terminology matters here. Teflon AF 2400 is a DuPont (now Chemours) trade name for a specific amorphous fluoropolymer grade — not a generic abbreviation for a category of film. The URF oxygen-permeable membrane discussed here belongs to this class of high-permeability amorphous fluoropolymer films, used for high-speed continuous photopolymerization.
4. Application on castable wax printers
TotusTec's URF-series oxygen-permeable DLP wax printers pair 4K DLP projection with a URF membrane for continuous exposure. Release force is exceptionally low and interlayer dimensional stability is maintained, allowing reliable printing of the CW2000 series (including CW2003) high-wax-content castable wax resins. Layer height is adjustable across 10 / 25 / 50 µm: at 25 µm, roughly 5 seconds per layer and about 18 mm of build height per hour; at 10 µm, roughly 3 seconds per layer. Surfaces come out fine and detail reproduction is sharp, suiting batch production of jewelry casting trees as well as complex designs — openwork, lightweight structures, pave and micro-pave settings, one-piece chains, and filigree.
The fully automatic URC series builds on this platform with automatic part removal, automatic resin replenishment, machine vision, and remote monitoring, supporting 24-hour continuous operation. The series name is Ultra-Rapid Continuous (URC).
5. Takeaway
Low-surface-energy release films and oxygen-permeable membranes represent two distinct paths. The first reduces interfacial adhesion to improve layer-by-layer peeling; the second uses an oxygen-inhibited interface to enable continuous building. Understanding where they differ — mechanism, parameter sensitivity, and application envelope — is what makes informed equipment selection and process optimization possible.
References and sources
[1] Chen Yuhang, Shen Jinfu, Yu Min, Han Xiaoyu. Design and process optimization of an intelligent monitoring system for DLP photopolymerization. Engineering Plastics Applications, 2025.
[2] Liang Yuxian, You Xiaoping, Shen Tingting, Zhang Junjie, Yu Xian, Zhang Wei. Study on release force in mask-image-projection photopolymerization 3D printing. Journal of Printing and Digital Media Technology Research, 2026.
[3] Tumbleston J R, et al. Continuous liquid interface production of 3D objects. Science, 2015, 347(6228): 1349–1352.
[4] Carbon 3D Inc. Continuous liquid interface production system with viscosity pump — patent literature.
Source note: all figures and conclusions above are taken from the abstracts of the cited papers without extrapolation. Product information comes from TotusTec specifications.
Keywords:
Related News
F2 Building 6A Jintong National Industrial Park No.8 Xihu Road Wujin District Changzhou City Jiangsu Province China
Follow Us
Copyright © 2022 Jiangsu Totustec. All Rights Reserved. 苏ICP备17013684号-1 Powered by:www.300.cn SEO
Online Message
Message
cn@totustec.com
+86 18112582262